Sharing Standard Templates for NetXMS

Started by darshakamodi, September 07, 2011, 08:10:13 AM

Previous topic - Next topic

Tursiops

#45
LSI MegaRAID SNMP Template (and rebranded versions of it)

Applies to:
- Windows Systems with a variation of "RAID Web Console" or "MegaRAID StorageManager" installed.

Requirements for Windows:
- Windows SNMP service needs to be installed prior to installing the Console.

Tursiops

#46
Lenovo XClarity SNMP Template

Applies to:
- Systems with SNMP Object ID of .1.3.6.1.4.1.19046.11.1

Tursiops

#47
Sophos Email Appliance SNMP Template

Applies to:
- Systems with SNMP Object ID of .1.3.6.1.4.1.2604 and an existing SNMP OID of .1.3.6.1.4.1.2604.2.1.1.2 which is not null.

Potential Issue:
On the system we monitor, the In-/Outbound Message counters seem to reset once a day, always at the same time, leading to nonsense values. A transform script was added to ignore such values. Depending on your email load, this may need to be adjusted (or a different solution found).

Tursiops

#48
WD MyCloud SNMP Template

Applies to:
- Systems with SNMP Object ID of .1.3.6.1.4.1.5127.1.1.1.2

Note:
- The Capacity Used % is a scripted DCI, the device itself does not provide a direct % for alerting. The DCI does not rely on the Total and Free DCIs, but collects both values independently via SNMP. If you have a range of these devices, it's probably worth changing the script.

Tursiops

#49
Synology NAS SNMP Template

Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.8072.* and a valid response for SNMP OID .1.3.6.1.4.1.6574.1.5.1.0.

Tursiops

#50
Netgear ReadyNAS SNMP Template

Applies to:
- Systems with SNMP Object ID matching  .1.3.6.1.4.1.4526.100.16.* or System Description matching "ReadyDATA OS".

Tursiops

#51
QNAP NAS SNMP Template

Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.24681.* and a valid response for SNMP OID .1.3.6.1.4.1.24681.1.4.1.1.1.1.4.2.0. (QNAP NAS Template)
- Systems with SNMP Object ID matching .1.3.6.1.4.1.24681.* and no valid response for SNMP OID .1.3.6.1.4.1.24681.1.4.1.1.1.1.4.2.0. (QNAP NAS (old) Template)

Notes:
I am unsure at which firmware version the new MIB kicked in. It also appears some older models even with the latest firmware are still using the old MIB. The extra check for the OID above seems to work well for identification though.

Also attached a separate template with three QNAP SNMP Traps (QNAP appears to simply send Inform/Warning/Error traps with different messages) and matching events.

Tursiops

#52
WatchGuard Firewall SNMP Template

Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.3097.* (WatchGuard Template)
- Systems with SNMP Object ID matching .1.3.6.1.4.1.3097.* and a valid response for SNMP OID .1.3.6.1.4.1.3097.6.6.1.0 (WatchGuard FireCluster Template)

Note:
- The Used RAM % is a scripted DCI, the device itself does not provide a direct % for alerting. The DCI does not rely on the Installed/Free RAM DCIs, but collects both values independently via SNMP. If you have a range of these devices, it's probably worth changing the script.

Also attached a separate template with a simple SNMP Trap for Alerts triggered by WatchGuards. Every alert triggers the same trap.
Configuring alerts via SNMP Traps is a bit of a pain in Watchguards, as you need to enable SNMP, configure the destination and enable alerts in every little service/proxy/whatever you might want to get alerts for..

Tursiops

SonicWALL SNMP Template

Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.8741.1

Note:
- The Concurrent Connections % is a scripted DCI, the device itself does not provide a direct % for alerting. The DCI does not rely on the Maximum and Current DCIs, but collects both values independently via SNMP. If you have a range of these devices, it's probably worth changing the script.

Tursiops

#54
Ruckus Brocade ICX SNMP Template

Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.1991.*, but not .1.3.6.1.4.1.1991.1.3.52.2.4.1.1.


Tursiops

TP Link Switch SNMP Template

Applies to:
- Systems with SNMP Object ID matching .1.3.6.1.4.1.11863.5.*

Note:
- We only monitor one of these and it's not returning a lot of data (that we found useful from a monitoring perspective), so the template is fairly simple.

Tursiops

UniFi Switch SNMP Template

Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.4413 and system description starting with "USW-".

Notes:
- We are monitoring only one of these and the above looks like it should work for other UniFi switches if this one device is anything to go by. Problem with .1.3.6.1.4.1.4413 is that it is the Broadcom Enterprise, so could potentially be matching a lot of other devices if it wasn't for the additional system description restriction. As all data for the UniFi switch is also located in the Broadcom Enterprise, this could maybe be turned into a more generic Broadcom template (someone with matching devices would be able to confirm this).

Tursiops

#57
Lenovo XClarity / IBM Integrated Management Console SNMP Traps Template

The traps all contain the same varbinds. The trap configuration in this template pick out the following:
- Datetime
- Priority
- Message Text
- Message ID Prefix

The Event includes the Datetime, Prefix and Message Text.
Priority is read inside the Event Processing policy, which changes the Events severity as needed. The policy is effectively used as "SNMP Trap Transform Script".

No policy for alerting is included, but that could be done inside the included policy or by adding another one below it (processing does not stop at the transform policy).

Tursiops

Cisco 3/4G SNMP Template

Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.9.1.* and a valid entry in the .1.3.6.1.4.1.9.9.661.1.1.1.1 table.

Tursiops

Xirrus Access Point SNMP Template

Applies to:
- Systems with SNMP Object ID .1.3.6.1.4.1.21013.1.*

Notes:
- Default SNMP Community for Xirrus access points is xirrus.