NetXMS Support Forum

it's possible to use HEAD parameter in ServiceCheck.HTTP request?
If possible, with the HEAD method to minimize traffic, bringing only the header.
Tks!

Hi all,

It's possible set comments on nodes or in containers and then make reading these comments for sending alerts?
The same thing to custom attributes.

Below a exemple of alerts we send:

Server: %n \\n
IP: %a \\n
Data: %t \\n
Event: %<dciDescription> \\n
Current Value: %<currentValue> \\n
Threshold: %<thresholdValue>

It's possible create a kiosk mode to web version or a viewer?
Show only a Predefined Graphics or a summary table, without menus etc..

Tks

Hi, it's me again

I Performed the update to version 2.0.3 netxms. And I used the update of the agents (Windows) centrally through the NPI.
Was performed successfully 70% both x86 as x64 Windows versions. However in the other 30% error occurred in the deploy.

In all cases the error was equal, the older version of the agent (2.0.2) has not been removed.
When you try to remove the agent manually (log in the server) error message appeared.
To install the new version was necessary to restart the servers after the process the 2.0.3 version was installed successfully.

Below is the image as well as the errors encountered in application logs.
The purpose of the post is trying to help so that the problem be identified:)

Anyway the success rate was very high which facilitated the upgrade process.     

Error from image:
Faulting application nxagentd.exe, version 0.0.0.0, time stamp 0x56a7b06b, faulting module libnxdb.dll!?
DBSetDebugPrintCallback@@YAXP6, version 6.0.6002.23154, time stamp 0x51da29f7, exception code 0xc0000139,
fault offset 0x00009f5d, process id 0xa80, application start time 0x01d18c32df60f7e0.


Log application:
Activation context generation failed for "C:\NetXMS\bin\nxagentd.exe".
Dependent Assembly Microsoft.VC80.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",
version="8.0.50727.6195" could not be found. Please use sxstrace.exe for detailed diagnosis.

Tks,

Hi all,

Looking im my event Configuration i see alot of these event Types:


DC_SERVER_THREAD_POOL_TOO_BUSY
Load average for server thread pool %6 is too high (%4)
Generated by server thread pool load average threshold

I need make somthing? i can delete these events?
Attached screen.

Tks

Hi all,

It's possible to extend process list information ( System.ProcessList ) adding CPU usage % and memory usage MB ?
It will usefull to see what are consuming resources from server without log in server

Tks alot

Hi all,

I would like to monitor the consumption of CPU and Memory from windows server process.
I saw that it is possible to list all the processes of a host via agent.
What I need is when you have for cpu consumption for exemple in 90% that I can list which this process consuming.
Is there any way?

Tks all

Hi all,

Im using ServiceCheck.HTTP to monitor local websites.
Sometimes we have timeout in these websites.
When this occour i see message <<< ERROR >>> in dci last values and no value is registered in history.

Is there any way to set a timeout in that request and register a value?
Example: if site not response in 5 minutes register value 10 in history.

I can use too ECS.HttpLoadTime to got response time from site, but without a timeout value and register i cant define some threholds.
Or tranformation script, like if website not response in 1000 ms write value 1000 so i can make a threhold based in values.

Tks a lot!

Good night to everyone,

I am using the netxms and enjoying it, however i need a help.
I would like to sum some dci values ​​from my nodes.
My nodes are inside containers Ex: Servers\Server1 , Servers\Web1
I would like to sum, For example , Network in and out and iis current users .
What is the  better way to do this ?
I search int forum a few examples , but I can not understand how to do it

Tks all.